WINDMILL ACCESSORIES |
DEAN BENNETT SUPPLY |
Download AY McDonald Float Valves page 66c in pdf
|
The AY McDonald Float Valve has a brass valve body that houses a rubber ball. The float arm is made of cast iron and is 19" long with a nole in the end for mounting a flat tank float. |
$ 33.75 |
1" #8713 AY McDonald float valve |
Download Midland Float Valves page 66b in pdf
| The Midland All-Brass float valves have a brass body with a
precision machined seat for the guide to set into. A leather washer is on top of the
guide, secured by a lid that attaches to the handle arm. The design gives you a positive
shut off every time. By removing the two screws and connecting the handle in position
perpendicular to that shown, the valve can be used on the side of the watering trough,
instead of the bottom. |
 |
|
||||
| $ 43.85 | 3/4" All Brass Float Valve | $ 103.90 | 2" All Brass Float Valve | |
| $ 58.60 |
1" All Brass Float Valve |
$ 162.30 | 2-1/2" All Brass Float Valve | |
| $ 71.10 |
1-1/4" All Brass Float Valve |
$ 190.55 | 3" All Brass Float Valve | |
| $ 85.15 |
1-1/2" All Brass Flaot Valve |
$ 285.00 | 4" All Brass Float Valve | |
|
|
||||
|
|
||||
| $ 1.30 |
3/4" Replacement Leathers |
$ 3.70 | 2" Replacement Leathers | |
| $ 1.35 |
1" Replacement Leathers |
$ 6.20 | 2-1/2" Replacement Leathers | |
| $ 1.60 |
1-1/4" Replacement Leathers |
$ 8.40 | 3" Replacement Leathers | |
| $ 2.15 |
1-1/2" Replacement Leathers |
$ 12.90 | 4" Replacement Leathers | |
|
|
HARD RUBBER FLAT FLOAT |
POLYETHYLENE COVERED FLAT FLOAT |
$ 26.50 |
#8715 Flat hard rubber float is used with any of the above float valves to control the water level in your stock tank. Rubber float measures 2-3/4" thick and 12" diameter, with a 3/8" hole in the center for mounting to the float valve. The durability of hard rubber floats make them attractive for use where livestock are rough on the tank float. |
|
$ 16.50 |
#8RSTF 8" Diameter Flat Reliable Tank Float that has corrosion resistant polyethylene covering over styrofoam core. Float is 3-1/4" thick and has a hole in the center. |
|
$ 18.15 |
#10RSTF 10" Diameter Flat Reliable Tank Float that has corrosion resistant polyethylene covering over styrofoam core. Float is 3-1/4" thick and has a hole in the center. |
|
| $ 20.25 | #12RSTF 12" Diameter Flat Reliable Tank Float that has corrosion resistant polyethylene covering over styrofoam core. Float is 3-1/4" thick and has a hole in the center. |
|
|
||
$ 32.25 |
R440-5 |
5" Round Copper Float Ball w/ 1/4" - 20 SAE Female Thread |
| $ 39.25 | R440-6 | 6" Round Copper Float Ball w/ 1/4" - 20 SAE Female Thread |
| $ 91.50 | R440-8 | 8" Round Copper Float Ball w/ 3/8" Female NPT Thread |
Download Rod Guides page 66 in pdf
| $ 11.75 | 5/8" x 2" Rod Guide | For use with 5/8" fiberglass sucker rod in 2" pipe. These guides act as centralizers for your rod, which helps prevent excessive rod wear and splintering. Manufacturer or rod recommends two guides per length of rod for optimum protection and long rod life. |
| $ 13.25 | 5/8" x 2-1/2" Rod Guide | For use with 5/8" fiberglass rod in 2-1/2" pipe |
$ 11.75 |
3/4" x 2" Rod Guide |
For use with 3/4" fiberglass rod in 2" pipe |
| $ 13.25 | 3/4" x 2-1/2" Rod Guide | For use with 3/4" fiberglass rod in 2-1/2" pipe |
| $ 20.75 | 3/4" x 3" Rod Guide | For use with 3/4" fiberglass rod in 3" pipe |
Download PVC Slotted Strainers page 67 in pdf
| $ 13.95 |  |
1-1/4" x 8" STRAINER | Schedule 80 heavy wall PVC plastic
pipe - finely mill slotted with 10 slot ( 10/1000" wide ) openings. Has 1-1/4" male pipe thread to screw directly into the bottom of your cylinder. Length is 8" with a flush bottom plug. |
|
| $ 15.95 | 1-1/2" x 8" STRAINER | Schedule 80 PVC strainer with 1-1/2" male NPT. | ||
| $ 17.50 | 2" x 8" STRAINER | Schedule 80 PVC strainer with 2" male NPT. | ||
| $ 59.95 | 1-1/4" STAINLESS STEEL STRAINER | Strainer has 4" of stainless
steel wire wrapped continuous slot ( 10 slot ) screen with plate bottom and 1-1/4" female NPT galvanized pipe connection. |
 |
Quick Disconnect #374 1/2 |
| $ 59.00 | The A-374-1/2 Quick Disconnect Pump Pole Adapter bolts on to your windmill's wood pump pole and has a spring loaded pin that will connect to either a hand pump or pump jack |
Download Flat Windmill Bar page 67 in pdf
| $ N / A | FP-51 FLAT WINDMILL BAR is 1/2" thick x 1" wide x 42" long flat steel bar with 7/16" male rod thread on one end. Two 1/2" holes are drilled thru the bar to allow for easy attachment of windmills and pump jacks to the sucker rod. |
Download Windmill Oil page 67 in pdf
 |
$ 3.50 $ 10.95 |
Quart of Windmill Oil Gallon of Windmill Oil |
Only $ 2.95 each in full case of 12 quarts. Only $ 8.95 each in full case of 4 gallons. |
Prices effective August 5, 2008
